Bk-precision 4078 - Manual Manual de usuario Pagina 8
- Pagina / 103
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
o Ramp down
o Noise
- Draw a line between any two points
- Clear (set to zero) any set of points or all points
- Set individual point values
After specifying a section of waveform memory for execution, the following parameters of the waveform can be
configured:
- Point rate (frequency)
- Peak-to-peak amplitude
- Offset voltage
1.4 Package Contents
The following list of items and accessories come in the package:
1. 4075 or 4078 DDS Function Generator
2. AC power cord
3. CD containing user manual and waveform creation software Wave-X
4. RS232 Serial Cable
Specifications
Models
4075
4078
Channels
1 Channel
2 Channels
Frequency
Characteristics
Sine
1 uHz to 25 MHz
Square
1 µHz to 25 MHz
Triangle, Ramp
1 µHz to 5 MHz
Pulse
1 mHz to 10 MHz
Accuracy
0.002 % (20 ppm)
Resolution
12 digits or 1 µHz
Arbitrary
Characteristics
Built-in Waveforms
Sine, Triangle, Square, Noise, Ramp Up, Ramp Down,
Sine(X)/X, Exponential Up, Exponential Down,
Gaussian
Waveform Length
2 points to 400,000 points
Vertical Resolution
14 bits (16,384 levels)
Noise
Add 1% to 100% to output waveform
Sampling Rate
100 MSa/s, Point execution rate: adjustable from 10 ns
to 50 s
Frequency Accuracy
0.005% (50 ppm)
Frequency Resolution
4 digits
Output
Characteristics
Amplitude Range
10 mV to 10 Vp-p into 50 ohms
Amplitude Resolution
3 digits (1000 counts)
Amplitude Accuracy (at 1 kHz)
± 1% ± 1 mV
Flatness (relative to 1 kHz)
± 0.2 dB to 1 MHz
± 1 dB to 25 MHz
Offset Range
± 5 V into 50 Ω, depending on the Amplitude setting
Offset Resolution
10 mV with 3 digits resolution
Offset Accuracy
± 1% ± 10 mV into 50 Ω
Output Impedance
50 Ω typical
Output Protection
The instruments output is protected against short
circuit or nominal accidental voltages applied to the
main output connector
- Safety Summary 3
- Table of Contents 5
- Section 1 7
- Specifications 8
- Modulation Combinations 10
- Section 2 11
- 2.6 Power Requirements 12
- 2.7 Grounding Requirements 12
- 2.8 Signal Connections 12
- 2.9 RS-232 Connection 12
- 2.11 GPIB Address 13
- 2.10 RS-232 Configuration 13
- Section 3 15
- 3.2 Display Window 16
- 3.3 Front Panel Controls 17
- 3.4 Back Panel Controls 17
- 3.5 Output connectors 18
- 3.6 MENU Keys 18
- 3.6.1 WAVEFORM Keys 20
- 3.6.2 MODE Key 22
- 3.6.3 ARBITRARY Key 23
- Start Address 25
- Markers 25
- 3.6.4 Arbitrary EDIT Menu 26
- 3.6.5 PULSE Menu 29
- 3.6.6 UTILITY Key 29
- 3.6.8 MODULATION Key 32
- 3.7 ON Key 34
- 3.8 Cursor Movement Keys 34
- 3.9 Rotary Input Knob 34
- 3.10 Power-On Settings 34
- 3.11 Memory 35
- 3.12 Displaying Errors 35
- 3.14 Examples 36
- 3.14.6 Using Voltage Offset 39
- 4.1 Overview 40
- 4.2 Device State 41
- 4.4 Device Address 41
- 4.5.1 The Input Buffer 42
- 4.5.2 The Output Queue 42
- 4.5.3 Response Messages 42
- 4.5.4 Coupled Commands 42
- 4.6 Block Data (GPIB Only) 43
- 4.8 Instrument Reset 43
- 4.9 Self Test 43
- 4.10 Command Syntax 43
- 4.11 Status Reporting 47
- 4.11.4 The Error Queue 48
- 4.11.5 Error Codes 48
- 4.12 Common Commands 51
- 4.13.1 SOURce Subsystem 55
- 4.13.1.2 Amplitude 57
- 4.13.1.3 Offset 57
- 4.13.1.5 Function 58
- 4.13.1.6 Point Rate 59
- 4.13.1.7 AM modulation 59
- 4.13.1.8 FM modulation 61
- 4.13.1.9 FSK modulation 62
- 4.13.1.10 Sweep control 64
- 4.13.1.11 PHASe adjust 66
- 4.13.1.12 PULSe setting 66
- 4.13.1.13 Duty Cycle 67
- 4.13.2 OUTPut Subsystem 68
- 4.13.2.1 Output State 68
- 4.13.3 Trigger Subsystem 68
- 4.13.3.1 Trigger Mode 69
- 4.13.3.2 Trigger Source 69
- 4.13.3.3 Burst Count 69
- 4.13.4 Arbitrary Subsystem 70
- 4.13.4.1 Point Rate 71
- 4.13.4.2 Address 71
- 4.13.4.3 Data 72
- 4.13.4.4 Line Draw 73
- 4.13.4.5 Clear 73
- 4.13.4.6 Copy 74
- 4.13.4.10 Start Address 76
- 4.13.4.11 Wavelength 76
- 4.13.4.12 Marker Address 76
- 4.13.4.13 Marker Length 77
- 4.13.4.14 Marker State 77
- 4.13.4.15 Save 77
- 4.13.5 Status Subsystem 78
- 4.13.5.1 Status Preset 78
- 4.13.5.2 Error Queue Read 78
- 4.13.5.3 Error Queue Enable 78
- 4.13.6 System Subsystem 81
- 4.13.6.3 SCPI Version 82
- 4.13.6.4 Security 82
- 4.13.6.5 Power-on Buffer 82
- 4.14.2 DCL - Device Clear 83
- 4.14.4 LLO - Local Lockout 83
- 4.15 SCPI Command Tree 84
- 4.15.4 :TRIGger Subsystem 85
- 4.15.5 :ARBitrary Subsystem 85
- 4.15.6 :STATus Subsystem 86
- 4.15.7 :SYSTem Subsystem 86
- 4.17.1 General 90
- Section 5 94
- 5.3 Performance Tests 95
- 5.3.3 Offset Accuracy 97
- 5.3.4 Sine Distortion 97
- 5.3.7 Operating Modes 98
- 5.3.10 RS232 Capability 100
- Performance Tests Results 101
Relacionado con productos y manuales para Generadores Bk-precision 4078 - Manual
Generadores Bk-precision 4079 - Manual Manual de usuario
(106 paginas)
(106 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales