Bk-precision 2516 - Manual Manual de usuario Pagina 7
- Pagina / 159
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
7
Safety Symbols
Electrical Shock hazard.
Refer to the operating user manual for warning information to
avoid hazard or personal injury and prevent damage to
instrument.
This symbol shows that the switch is a power switch located at
the front panel. Pressing this button turns on the oscilloscope,
and holding it down for a few seconds turns off the
oscilloscope.
CATI
CATII
Category I overvoltage conditions.
Measurement instruments whose measurement inputs are
not intended to be connected to the mains supply. The
voltages in the environment are typically derived from a
limited-energy transformer or a battery.
Category II overvoltage conditions.
Measurement instruments whose measurement inputs are
meant to be connected to the mains supply at a standard wall
outlet or similar sources.
CATIII
Category III overvoltage conditions.
Measurement instruments whose measurement inputs are
meant to be connected to the mains installation of a building.
Maximum Input Voltages
Oscilloscope Inputs
Maximum input voltage to CH1 and CH2 BNC direct(1:1) - CATII 300V
RMS, CATI 150V RMS
Maximum input voltage to CH1 and CH2 BNC via 10:1 probe PR250SA
(included with models 2515 and 2516) - CATII 1000V RMS, CATIII 600V
RMS
- 2510 Series Handheld Digital 1
- Storage Oscilloscopes 1
- Safety Summary 2
- Compliance Statements 5
- CE Declaration of Conformity 6
- Safety Symbols 7
- Environmental Conditions 9
- Table of Contents 10
- List of Figures 14
- 1 General Information 16
- 1.2 Package Contents 17
- 1.3 Front Panel Overview 18
- 1.4 Top View 20
- 1.5 Rear Panel Overview 20
- 1.6 Side Panel Overview 21
- 1.7 Display Overview 22
- Digital Multimeter Display 24
- Recorder/Trend Plot Display 25
- 1.8 Protection Fuse 26
- 1.10 Probes 27
- 2 Getting Started 28
- Battery Operation 29
- 2.2 Tilt Stand 30
- 2.3 Power On Device 30
- Figure 10 - Boot Screen 31
- 2.5 Set to Factory Default 32
- 2.6 Configure Date and Time 35
- 2.7 Probe Compensation 36
- 3 Using the Oscilloscope 39
- 3.2 Channel Menu 40
- Channel Coupling 41
- Bandwidth Limit 41
- Vertical Scale 41
- Probe Attenuation Scale 41
- Invert Waveform 42
- Digital Filter 42
- Auto Setting 43
- 3.4 Scope Menu 44
- Display Menu 45
- Table 6 - Display Menu 1/2 46
- Table 7 - Display Menu 2/2 46
- Figure 16 - XY Mode 47
- Math Menu 49
- Table 8 - Math Menu 1/2 50
- Table 9 - Math Menu 2/2 50
- Table 10 - FFT Menu 1/2 51
- Table 12 - FFT Menu 2/2 52
- Horizontal System 54
- Delay Scan 56
- Deep Memory 57
- Vertical System 60
- Adjust Vertical Scale 61
- Reference Waveform Menu 62
- Saving a Reference Waveform 63
- 3.5 Trigger System 64
- Edge Trigger 65
- Pulse Trigger 67
- Video Trigger 69
- Slope Trigger 72
- Alternative Trigger 74
- 3.7 Save/Recall Function 76
- Table 26 - Save/Recall Menu 77
- Figure 41 - Save Progress 81
- Saving Screen Capture 83
- Saving Waveform Data 83
- 3.8 Utility Menu 84
- Table 30 - Utility Menu 2/4 85
- Table 31 - Utility Menu 3/4 85
- Check System Information 86
- Enable/Disable Key Sound 87
- Set the Language 88
- Updating Firmware 88
- Set Screen Saver 90
- Waveform Record Function 90
- Configure Waveform Record 91
- Playback Recorded Waveform 93
- Measurement Functions 94
- Time Measurement Parameters 96
- Delay Measurement Parameters 97
- Display All Measurements 98
- Cursor Functions 101
- Track Cursor Mode 104
- Auto Cursor Mode 105
- DC Voltage Measurement 110
- AC Voltage Measurements 112
- DC Current Measurements 114
- Make AC Current Measurements 116
- 4.4 Make Diode Measurements 120
- 4.5 Continuity Test 121
- 4.7 Using Trend Plot 124
- 5 Using the Recorder 125
- Record Data with Trend Plot 127
- Pause Recording 128
- Restart Recording 128
- Select Display Mode 128
- Scope Recorder 130
- Table 52 - Option Menu 132
- Configure Record Options 133
- Start Scope Recording 133
- Playback Scope Recording 134
- Meter Trend Plot 136
- 6 Remote Communication 142
- 7 Troubleshooting Guide 143
- Frequency Asked Questions 144
- Multimeter 145
- 8 Specifications 146
- Maximum Input Voltages 150
- Multimeter Specifications 152
- General Specifications 155
- 11 Maintenance 156
- SERVICE INFORMATION 157
- LIMITED THREE-YEAR WARRANTY 158
Relacionado con productos y manuales para Herramientas Bk-precision 2516 - Manual
(2 paginas)
(5 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales