Bk-precision 2516 - Manual Manual de usuario Pagina 118
- Pagina / 159
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
118
4.3 Make Resistance Measurements
To measure resistances, press repeatedly until Meter is set to
“Res.”.
Table 45 – Resistance Measurement Menu
Menu Option
Setting
Description
Relative
On
Save the current input value as a reference
value. Subsequent measurements will be the
difference from the reference value. This is
same as “zeroing” the meter.
Off
Relative mode is disabled.
Auto
Select to enable autoranging.
Manual
Select to enable manual ranging.
V
Display measurement in volts (V). In manual
ranging, only the volts (V) ranges are
selectable.
mV
Display measurement in millivolts (mV). In
manual ranging, only the millivolts (mV) ranges
are selectable.
Trend Plot
Enters the Meter Trend plot mode (See “Meter
Trend Plot” for more information).
Configure all settings from the menu.
When set for Manual ranging (select Manual by toggling ), use the
key to increase the range. At the highest range, pressing this will
automatically go back to the lowest range.
Resistance ranges: 600 Ω, 6 kΩ, 60 kΩ, 600 kΩ, 6 MΩ, and 60 MΩ.
- 2510 Series Handheld Digital 1
- Storage Oscilloscopes 1
- Safety Summary 2
- Compliance Statements 5
- CE Declaration of Conformity 6
- Safety Symbols 7
- Environmental Conditions 9
- Table of Contents 10
- List of Figures 14
- 1 General Information 16
- 1.2 Package Contents 17
- 1.3 Front Panel Overview 18
- 1.4 Top View 20
- 1.5 Rear Panel Overview 20
- 1.6 Side Panel Overview 21
- 1.7 Display Overview 22
- Digital Multimeter Display 24
- Recorder/Trend Plot Display 25
- 1.8 Protection Fuse 26
- 1.10 Probes 27
- 2 Getting Started 28
- Battery Operation 29
- 2.2 Tilt Stand 30
- 2.3 Power On Device 30
- Figure 10 - Boot Screen 31
- 2.5 Set to Factory Default 32
- 2.6 Configure Date and Time 35
- 2.7 Probe Compensation 36
- 3 Using the Oscilloscope 39
- 3.2 Channel Menu 40
- Channel Coupling 41
- Bandwidth Limit 41
- Vertical Scale 41
- Probe Attenuation Scale 41
- Invert Waveform 42
- Digital Filter 42
- Auto Setting 43
- 3.4 Scope Menu 44
- Display Menu 45
- Table 6 - Display Menu 1/2 46
- Table 7 - Display Menu 2/2 46
- Figure 16 - XY Mode 47
- Math Menu 49
- Table 8 - Math Menu 1/2 50
- Table 9 - Math Menu 2/2 50
- Table 10 - FFT Menu 1/2 51
- Table 12 - FFT Menu 2/2 52
- Horizontal System 54
- Delay Scan 56
- Deep Memory 57
- Vertical System 60
- Adjust Vertical Scale 61
- Reference Waveform Menu 62
- Saving a Reference Waveform 63
- 3.5 Trigger System 64
- Edge Trigger 65
- Pulse Trigger 67
- Video Trigger 69
- Slope Trigger 72
- Alternative Trigger 74
- 3.7 Save/Recall Function 76
- Table 26 - Save/Recall Menu 77
- Figure 41 - Save Progress 81
- Saving Screen Capture 83
- Saving Waveform Data 83
- 3.8 Utility Menu 84
- Table 30 - Utility Menu 2/4 85
- Table 31 - Utility Menu 3/4 85
- Check System Information 86
- Enable/Disable Key Sound 87
- Set the Language 88
- Updating Firmware 88
- Set Screen Saver 90
- Waveform Record Function 90
- Configure Waveform Record 91
- Playback Recorded Waveform 93
- Measurement Functions 94
- Time Measurement Parameters 96
- Delay Measurement Parameters 97
- Display All Measurements 98
- Cursor Functions 101
- Track Cursor Mode 104
- Auto Cursor Mode 105
- DC Voltage Measurement 110
- AC Voltage Measurements 112
- DC Current Measurements 114
- Make AC Current Measurements 116
- 4.4 Make Diode Measurements 120
- 4.5 Continuity Test 121
- 4.7 Using Trend Plot 124
- 5 Using the Recorder 125
- Record Data with Trend Plot 127
- Pause Recording 128
- Restart Recording 128
- Select Display Mode 128
- Scope Recorder 130
- Table 52 - Option Menu 132
- Configure Record Options 133
- Start Scope Recording 133
- Playback Scope Recording 134
- Meter Trend Plot 136
- 6 Remote Communication 142
- 7 Troubleshooting Guide 143
- Frequency Asked Questions 144
- Multimeter 145
- 8 Specifications 146
- Maximum Input Voltages 150
- Multimeter Specifications 152
- General Specifications 155
- 11 Maintenance 156
- SERVICE INFORMATION 157
- LIMITED THREE-YEAR WARRANTY 158
Relacionado con productos y manuales para Herramientas Bk-precision 2516 - Manual
(2 paginas)
(5 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales